المواد: جلد البقر
لشركة Thor Soft Hammers
صنع في بريطانيا العظمى
Φ 25mm
الوزن الإجمالي: 20 جرام
* 1: يجب استبدال وجه المطرقة قبل حدوث تلف للرأس. أولاً ، تأكد من أن المقبض غير تالف. في حالة تلفه ، يجب استبداله بواحد مما يلي بحجم وشكل ونوع المقبض الصحيح. تأكد أيضًا من أن المقبض ليس مفكوكًا في الرأس. إذا تم فك المقبض ، فيجب إعادة حمايته أو استبداله ، إن أمكن.
* 2: قص وإزالة أكبر قدر ممكن من الوجه القديم. احفر حفرة في وسط الوجه مع الحرص على عدم الثقب في الوجه. قم بإزالة أكبر قدر ممكن من الوجه باستخدام المثقاب السفلي أو آلة الطحن ذات المسطح.
* 3: قد تكون قادرًا على الإمساك بمركز سطح الجلد القديم وطيه للداخل في هذه الحالة
* 4: بمجرد إزالة الوجه القديم ، أدخل الوجه الجديد. يجب أن تكون الحافة مفتوحة بما يكفي لتناسب الوجه الجديد. أفضل طريقة لإجراء هذه العملية هي الجمع بين الضغط المناسب وأداة الفتح / الإغلاق.
* 5: مع وضع الوجه الجديد في مكانه ، اعكس أداة الدمج وأغلقها حول الوجه الجديد بالضغط المناسب. مرة أخرى ، يجب إغلاق الحافة بما يكفي لتثبيت الوجه في مكانه. عند تركيبه بشكل صحيح ، يمكن تدوير الوجه.
* 6: يستبدل العديد من العملاء جانب الجلد ، لكن الجانب النحاسي المستخدم يصعب إزالته بشكل خاص. تحتوي المقابس النحاسية على أخاديد صغيرة تسمح للنحاس بالانتشار أثناء الاستخدام. النحاس الذي نستخدمه هو 99٪ نقي وناعم ويمكن أن يتحول إلى فطر على رأس المطرقة بعد استخدام كبير. بمجرد أن يتحول السطح ، اعتمادًا على التطبيق ، سيستمر النحاس إلى أجل غير مسمى تقريبًا في هذه الحالة دون مزيد من التشوه. يجد العديد من العملاء أن استخدام الطرف النحاسي للكسر أكثر اقتصادا.
* يرجى ملاحظة أن مواصفات المنتج قد تتغير بسبب أسباب الشركة المصنعة.
Material: cowhide
for Thor Soft Hammers
Made in Great Britain
Φ 25 mm
Gross weight: 20 g
*1: The face must be replaced before any damage occurs to the hammer head.First, make sure that the handlebar is not damaged.If it is damaged, it should be replaced with one of the followingCorrect size, shape and type of handle.Also make sure the handlebar is not loose in the head.If the handlebar is loosened, it must be re-protected or replaced, if possible.
*2: Cut and remove as much of the old surface as possible.Drill a hole in the center of the face, taking care not to drill into the face.Use a bottom drill or milling machine to use the flats and remove as much of the face as possible.
*3: You may be able to grab the center of the old skin surface and fold it inward in that case.
*4: After the old side is removed, insert the new side.The rim must be opened just enough for the new surface to fit.The best way to perform this operation is a combination of a suitable press and an opening / closing tool.
*5: With the new face in place, reverse the combination tool and close it around the new face with a suitable press.Again, the rim is closed enough to hold the face firmly in place.When correctly mounted, the face can be rotated.
*6: Many customers replace the skin face, but the used copper face is particularly difficult to remove.Copper sockets have small grooves in them, and the copper will enlarge during use.The copper applied to the products is 99% pure, soft, and can mushroom on the hammerhead after considerable use.In this state, depending on the application, the copper lasts almost indefinitely without further deformation once the surface has been set.Many customers find it more economical to use the copper end for destruction.
*There may be changes in product specifications due to the manufacturer's reasons.