القرص (الدوار الداخلي) ・ ضرس خلفي إلخ.. ، مادة اللوحة: ألومنيوم 2 قطعة.
• الحجم الداخلي للصندوق: حوالي 30 سم × 30 سم × 5.5 سم
* من المستحيل أن تطلب من الخارج
* تُظهر الصورة جهاز Alma Box Hard 20.
[ملاحظات حول خدمة الأكسدة "KOKEN ALMA BOX Hard for Plate"].
نشكرك على شراء "Koken ALMA BOX Hard for 1 Plate" و "Koken ALMA BOX Hard for 2 Plates".
يصف هذا المستند الاحتياطات الواجب اتخاذها عند طلب المعالجة بأكسيد الألومنيوم باستخدام "KOKEN ALMA BOX Hard for 1 Plate" و "KOKEN ALMA BOX Hard for 2 Plates".
لا يجوز لك استخدام هذه الخدمة إلا إذا كنت قد قرأت هذا الإشعار بعناية وقمت بالتوقيع والتحقق من نموذج الموافقة المرفق.
إذا كنت لا توافق على شروط هذه الاتفاقية ، ولا توقع أو تحدد المربع ، أو لم تقم بملء المعلومات المطلوبة ، فلن نقبل طلبك لهذه الخدمة.
شكرا لتفهمك.
[ترتيب ملاحظات]
يمكنك طلب قطعة واحدة فقط لـ "KOKEN ALMA BOX Hard for 1 Plate" أو جزئين لـ "2 Plates" من نفس اللون.
في مثل هذه الحالة ، سيتم احتساب فرق السعر بشكل منفصل عن طريق الدفع نقدًا عند التسليم.
الأجزاء التي سيتم وضعها في "KOKEN ALMA BOX Hard for Plate" تقتصر على الأقراص (الدوارات الداخلية) والعجلات المسننة الخلفية ومنتجات الألومنيوم الأخرى.
يمكن تطبيق الألمنيوم المؤكسد فقط على منتجات الألمنيوم.
من فضلك لا تضيف معادن أخرى (الحديد ، الفولاذ المقاوم للصدأ ، التيتانيوم ، النحاس ، إلخ.).
من حيث المبدأ ، لن يتم استرداد أي مبالغ مستردة حتى إذا لم تكن راضيًا عن المنتج النهائي بعد التوقيع على الاتفاقية المرفقة واستمارة الطلب وملئها.
شكرا لتفهمك.
إذا لم نتمكن لسبب ما من طلاء الجزء الذي أرسلته إلينا بأكسيد الألومنيوم ، أو إذا كان الجزء الذي أرسلته إلينا مختلفًا عن الجزء الذي طلبته ، فسنرسله إليك مرة أخرى بالدفع عند التسليم.
شكرا لتفهمك.
[ملاحظات الشحن]
يرجى التأكد من أن العبوة لا تخدش أو تنبعج الأجزاء المهمة.
يرجى ملاحظة أن Koken ليست مسؤولة عن أي ضرر أو خدوش تحدث أثناء النقل.
يرجى ملء عدد الأجزاء في نموذج الطلب المرفق.
إذا لم تقم بملء النموذج ، فيرجى ملاحظة أنه لا يمكننا قبول أي مطالبة تتعلق بفقدان الأجزاء.
عند شحن الأجزاء ، يرجى التأكد من استخدام قسيمة الشحن (فاتورة) المدرجة في الحزمة.
إذا كنت تستخدم أي فاتورة أخرى ، فسنقوم بإرسال العنصر إليك بدون معالجة.
في هذه الحالة ، سوف نفرض عليك رسوم المناولة والشحن عند التسليم.
شكرا لتفهمك.
[ملاحظات على أنودة]
يختلف اللون الطبيعي لعملية الأنودة الصلبة عن عملية الأنودة العادية ، والتي تستخدم الأصباغ لإضافة اللون وتشكيل فيلم أكسيد ، وهي عملية خاصة تتكون من طبقة أكسيد قوية جدًا دون استخدام الأصباغ.
لذلك ، يرجى فهم أن لون المنتج النهائي قد يختلف اعتمادًا على ظروف المادة وطريقة التصنيع ، وما إلى ذلك ، لأننا لا نستخدم الصبغة.
يرجى ملاحظة أننا لا نقبل أي ادعاءات بخصوص لون المنتج.
عند طلب أسنان العجلة المسننة ، يرجى تفكيك جميع الأجزاء المناسبة للضغط قبل الشحن.
يرجى ملاحظة أنه لا يمكن إجراء عملية الأنودة إذا كانت الأجزاء مناسبة للضغط وما إلى ذلك. تظل.
عند طلب دوارات القرص ، تأكد من شحن الدوار الداخلي فقط.
يرجى ملاحظة أن المسامير العائمة ليست مؤكسدة في هذه الخدمة.
الرجاء استخدام الخدمة المناسبة لمنتجك.
بعض الأجزاء مطلية بدلاً من أنود.
في هذه الحالة ، يتم استخدام السفع الرملي كعملية تجريد.
سيتم احتساب تكلفة السفع الرملي بشكل منفصل نقدًا عند التسليم.
يرجى ملاحظة أن KOKEN ليست مسؤولة عن أي عيوب في الألومنيوم المؤكسد ناتجة عن بقايا الطلاء المتروكة على السطح عندما يزيل العميل الطلاء بنفسه.
قد تكون بعض الأجزاء مطلية.
في هذه الحالة ، سوف نفرض عليك رسومًا مقابل أعمال التجريد بشكل منفصل أو نعيد القطعة بدون معالجة.
يرجى تنظيف الأجزاء التي ترسلها إلينا بنفسك.
نظرًا لعملية الأنودة ، ستقوم KOKEN بتنظيف المنتج ، ولكن قد لا يكون من الممكن إزالة الزيت والشحوم الملتصقة بعامل قفل الخيط وفتحات المسامير التي لم يتم اختراقها.
إذا أصبحت هذه المواد الغريبة آثارًا مقنعة أو تقطر في مكان ما في عملية العلاج ، فقد تتسبب في حدوث عيوب انودية (تفاوت في الصباغة ، التقشر ، إلخ.).
يرجى ملاحظة أن KOKEN ليست مسؤولة عن مثل هذه الحالات.
تتميز عملية الأنودة بأنها تعتمد على المادة كثيرًا.
منتجات الصب (بما في ذلك المنتجات المصبوبة التي غالبًا ما تستخدم لقطع غيار الدراجات النارية الأصلية) عرضة للون غير المتساوي أو الصباغة غير المتساوية لأن تركيب المادة ليس ثابتًا ، والمادة نفسها قد لا تكون مصبوغة مع تغير اللون أو قد تكون مصبوغة بشكل غامق.
نظرًا لاختلاف المواد ، لن يكون لجميع الأجزاء التي تطلبها نفس النهاية.
هذه ظاهرة لا يمكن تجنبها بسبب خصائص الأنودة ، لذا يرجى الانتباه إلى ذلك قبل الطلب.
يرجى ملاحظة أن KOKEN لن تقبل أي مطالبات حتى إذا كانت الأجزاء المطلوبة غير مرضية لأن بعض المنتجات لا تظهر للعين.
لا ينصح بتقشير الألمنيوم المؤكسد بنفسك عند إعادة المعالجة بأكسيد الألومنيوم.
في KOKEN ، تتوفر إعادة المعالجة بالأنودة بسعر يتضمن تجريد أنودة.
عملية الأنودة هي إحدى العمليات التي تؤثر بشكل كبير على النهاية.
إذا قمت بعمل التجريد بنفسك ، فقد يتسبب ذلك في مشاكل مثل "سطح خشن من الألومنيوم" أو "لون سطح غريب".
يرجى ملاحظة أن KOKEN ليست مسؤولة عن مثل هذه الحالات.
يعتمد إنهاء إعادة الطلاء بأكسيد الألومنيوم على مادة الألمنيوم.
كما يعكس الوضع الحالي للأجزاء.
ستختفي الأجزاء المحفورة بالليزر عن طريق إعادة المعالجة بالأكسيد (ستبقى علامة الحرف).
شكرا لتفهمك.
عند إعادة التجديد ، ستفقد الأجزاء التي تحتوي على أجزاء مناسبة للضغط.
سيكون خلوص الجزء الملائم للضغط من المحمل والجزء الذي تم تعليق الدبوس فيه أوسع من قبل المعالجة.
هذه ظاهرة لا يمكن تجنبها بسبب خصائص عملية إعادة الأكسدة ، لذا يرجى الانتباه لها والاعتناء بها بنفسك.
كوركين غير قادر على الإجابة على أسئلتك حول كيفية التعامل مع المشكلة.
إذا كانت هناك خدوش أو تآكل على الأجزاء التي تستخدمها الآن ، فسيتم معالجتها بأكسيد الألومنيوم كما هي ، وبالتالي لن تختفي الخدوش وعلامات التآكل والخدوش.
لا تضمن إعادة الطلاء بأكسيد الألومنيوم أن يبدو الجزء وكأنه جديد.
المنتجات التي تتكون من أجزاء متعددة (الأجزاء المرتبطة بتركيبات الضغط ، إلخ.) قد تتلطخ فقط في الجزء الذي تتدفق فيه الكهرباء بسبب طبيعة الأنودة.
بالإضافة إلى ذلك ، هناك حالة يحدث فيها الترهل من جزء المفصل لكل جزء ، ويصبح سببًا لعيب الألمنيوم المؤكسد (تفاوت الصباغة ، التقشر ، إلخ.).
شكرا لتفهمك.
في حالة وجود عيب في عملية الطلاء بالأنودة بسبب إهمال شركة KOKEN ، من حيث المبدأ ، ستضمن KOKEN فقط تكلفة معالجة المنتج المعيب.
لا يغطي الضمان أي مسؤولية ثانوية أخرى.
شكرا لتفهمك.
[ملاحظة عن وقت التسليم]
يرجى ملاحظة أنه سيتم تمديد تاريخ التسليم في حالة وجود سهو في المعلومات المطلوبة.
إذا كانت هناك أي أجزاء لا يمكن معالجتها بأكسيد الألومنيوم كما هي أثناء الفحص بعد الوصول ، فسنقوم بالاتصال بالعميل للتأكيد.
في هذه الحالة ، سيتم تمديد وقت التسليم بسبب انقطاع العمل.
■Disc (inner rotor), rear sprocket, etc., 2 sheets of plate aluminum products
■Inner dimensions of the box: Approx. 30cm x 30cm x 5.5cm
*Not available for overseas orders
*The image shows the Alma Box Hard 20.
[Notes on the anodizing service "KOHKEN ALMA BOX Hard for Plate"]
Thank you for purchasing "Koken ALMA BOX Hard for 1 Plate" and "Koken ALMA BOX Hard for 2 Plates".
This document describes the precautions to be taken when requesting anodizing with "Kohken ALMA BOX Hard for 1 Plate" and "Kohken ALMA BOX Hard for 2 Plates".
You may use this service only if you have read this notice carefully and have signed and checked the attached agreement.
If you do not agree to the terms of this agreement, do not sign or check the box, or do not fill in the required information, you will not be accepted for this service.
[Order Notes]
・You can order only one part for "KOKEN ALMA BOX Hard for 1 Plate" or two parts for "for 2 Plates" in the same color.
In such a case, the difference in price will be charged separately by cash on delivery.
・The parts to be packed in "KOKEN ALMA BOX Hard for Plate" are limited to discs (inner rotors), rear sprockets and other plate aluminum products.
Anodized aluminum can only be applied to aluminum products.
Please do not add other metals (iron, stainless steel, titanium, copper, etc.).
・In principle, no refunds will be made even if you are not satisfied with the finished product, as long as you have filled out the attached consent form.
・If for some reason KOHKEN is unable to anodize the part you have sent them, or if the part you have sent them is different from the one you have ordered, they will send it back to you with payment on delivery.
[Shipping Notes]
・Please make sure that the packaging does not scratch or dent the important parts.
Please note that Koken is not responsible for any damage or dents caused during transportation.
・Please fill in the number of parts on the attached application form.
If you do not fill in the form, please note that Kohken cannot accept any claim for loss of parts.
・When shipping out the parts, please make sure to use the shipping slip (invoice) included in the package.
If you use any other invoice, we will send the item back to you unprocessed.
In that case, it will charge you the handling and shipping fees on delivery.
[Notes on anodizing]
・The natural color of the hard anodizing process is different from the normal anodizing process, which uses dyes to add color and form an oxide film, and is a special process that forms a very strong oxide film without using dyes.
Therefore, there are no dyes applied and the coloring is resulted by materials or procedure.
Please note that any claims regarding the color of the product not accepted.
・When ordering sprockets, please disassemble all press-fit parts before shipping them out.
Please note that anodizing cannot be performed if press-fit parts, etc. remain.
・When ordering disc rotors, make sure to ship the inner rotor only.
Please note that the floating pins are not anodized in this service.
Please use the appropriate service for your product.
・Some parts are painted instead of being anodized.
In this case, sandblasting is used as a stripping process.
The cost of sand blasting will be charged separately by cash on delivery.
Please note that KOKEN is not responsible for any anodized aluminum defects caused by paint residue left on the surface when the customer removes the paint by himself.
・Some parts may be plated.
In that case, it will charge you for the stripping work separately or return the part without processing.
・Please clean the parts beforehand as sending it back to KOHKEN DENKA.
Due to the process of anodizing, KOKEN will clean the product, but it may not be possible to completely remove the oil and grease adhering to the thread locking agent and the screw holes that are not penetrated.
If those foreign substances become masking effects or drip somewhere in the treatment process, it may cause anodic defects (unevenness in dyeing, flaking, etc.).
Please note that KOKEN is not responsible for such cases.
・The anodizing process has the property that it depends on the material very much.
Cast products (including die-cast products which are often used for motorcycle stock parts) are prone to uneven color or uneven dyeing because the composition of the material is not constant, and the material itself may not be dyed with discoloration or may be dyed darkly.
Due to the difference of materials, not all the parts you request will have the same finish.
This is an unavoidable phenomenon due to the characteristics of anodizing, so please be aware of this before ordering.
Please note that KOKEN will not accept any claims even if the requested parts are not satisfactory because some products are not apparent to the eye.
・It is not recommended to peel off the anodized aluminum by yourself when re-anodizing.
At KOKEN, re-anodizing is available at a price that includes anodizing stripping.
The anodizing exfoliation process is one of the processes that greatly affects the finish.
If you do the exfoliation work by yourself, it may cause problems such as "rough surface of aluminum" or "strange surface color".
Please note that KOKEN is not responsible for such cases.
・The finish of re-anodizing depends on the material of aluminum.
It also reflects the current status of the parts.
The laser etched parts will disappear by re-anodizing (the character mark will remain).
・When reanodizing, the cylinders with press-fit parts will become loose.
The clearance of the press-fit part of the bearing and the part where the pin is stuck will be wider than before processing.
This is an unavoidable phenomenon due to the characteristics of anodizing, so please be aware of this before ordering.
KOKEN will not answer your questions about how to deal with the problem.
・If there are scratches or corrosion on the parts you currently use, they will be anodized as they are, so the scratches, corrosion marks and dents will not disappear.
Re-anodizing does not guarantee that the part will look like new.
・Products consisting of multiple parts (parts joined by press fitting, etc.) may be stained only in the part where electricity is flowing due to the nature of anodizing.
In addition, there is a case that sagging occurs from the joint part of each part, and it becomes the cause of the anodized aluminum defect (unevenness of dyeing, flaking, etc.).
・In the event of a defect in the anodizing process due to the negligence of KOHKEN, in principle, KOHKEN will only guarantee the cost of treatment of the defective product.
The warranty does not cover any other secondary liability.
[Note on delivery time]
Please note that the delivery date will be extended if there are omissions in the required information.
・If there are any parts that cannot be anodized as they are during the inspection after arrival, KOHKEN will contact the customer for confirmation.
In that case, the delivery time will be extended due to the interruption of work.