[بحجم]
عرض : حوالي 760mm
طول الجبهة / الخلفية : ما يقرب من 500 ملم
ارتفاع : حوالي 520 ملم
[مواد]
FRP
محتويات المنتج
هيكل الطربوش ، الشاشة ، مجموعة برغي الشاشة
* هذا الطربوش منتج للأغراض العامة مصنوع في الخارج ، لذلك قد يكون هناك خدوش وخدوش وفرك ، إلخ.. قد يتسبب ذلك في عدم احتواء الثقوب ، وقد يلزم تعديلها للتثبيت. يرجى التأكد من فهم ما يلي قبل الشراء.
* قد تتداخل وحدة الضوء والطربوش مع بعضهما البعض ، وفي هذه الحالة يجب إزالة الجزء المتداخل من القلنسوة.
* قد تتداخل الشوكة والقلنسوة مع بعضهما البعض ، لذلك تحتاج إلى التحقق من نطاق حركة الجانبين الأيمن والأيسر وحلق القلنسوة إذا كان هناك تداخل.
* يجب قطع الأجزاء المتداخلة الأخرى أو حلقها أو معالجتها بطريقة أخرى.
* بالنسبة لوحدات الإضاءة التي تُباع بشكل منفصل ، يجب تصنيع حزام تمديد من الحزام الرئيسي.
* الثقب بين الوقف والغطاء قد يتغير حسب موضع القلنسوة. في هذه الحالة ، تحتاج إلى توسيع الفتحة الموجودة في القلنسوة.
* هناك حالات لا تتطابق فيها فتحات الشاشة والقلنسوة ، وفي هذه الحالة تحتاج إلى إصلاح فتحات الشاشة والقلنسوة من الفتحة المركزية للقلنسوة إلى الخارج بجوز جيد ، ثم توسيع الأجزاء التي لا تتطابق مع ملف.
* لا تحتوي بعض القطع على فتحة في جانب القلنسوة للشاشة. في هذه الحالة ، قم بحفر الثقوب لتتناسب مع الشاشة.
* طرق المعالجة بخلاف تلك المذكورة هنا غير متوفرة ، لذا يرجى التحقق من السيارة الفعلية.
* المنتج خاضع للمعالجة ، لذلك لا يمكننا قبول المرتجعات لعدم القدرة على تثبيته.
* يرجى التأكد من معالجة المنتج وتثبيته قبل الطلاء. لن يتم قبول أي مطالبات بعد الطلاء.
* يرجى ملاحظة أن مواصفات المنتج قد تتغير بسبب سبب الشركة المصنعة.
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
Components
Cowl body, windshield, windshield screw set
*Bracket and light unit sold separately.
*Please make sure to read the notes before purchasing.
*Bracket kits for DYNA, XL, MILWAUKEE FXBB and FXLR are available (sold separately)
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*For light units sold separately, it is necessary to make an extension harness from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.