[التوافق]
· قطر المقود: .222.2
قبضة القطر الخارجي: Φ33
· طول القبضة المقابلة: 115/120/130 ملم
・ منتج حصري لسيارة 12V
[وشملت أجزاء:] أنبوب الحرارة يتقلص لحماية قبضة
* قطر مقبض صغير (Φ22.2 أو أقل) المركبات والقضبان بوصة (Φ25.4) ، سعة البطارية · لا يمكن استخدامها للسيارات ذات توليد الطاقة المنخفض. (يتطلب بدء التشغيل الجهد 12.5V)
* لربط كم تمديد الموردة ، وتطبيق لاصق على المنطقة حيث يتم تركيب كم تمديد مع قبضة ، وتجعيد بحزم. إذا تم تطبيق الحمل الشديد على كم تمديد ، قد تمتد الأكمام تمديد أو قبضة نهاية وتمديد يرجى ملاحظة أن هذا سوف يسبب ضررا على الأكمام.
* بسبب تبديد الحرارة عن طريق المقبض ، ونهاية الشريط ، والقفازات ، والتبريد عن طريق تشغيل الرياح ، فقد تكون درجة الحرارة الحسية منخفضة.
* استخدم مسدسًا حراريًا لتوصيل الأنبوب القابل للتقلص من الحرارة المضمّن لحماية القبضة ، وعند تسخين سخان القبضة ، قد يصبح الأنبوب الواقي المرفق ناعماً ويرخي بسبب الحرارة ، لذا قم بتثبيته عندما لا يكون المدفأة قيد الاستخدام. فمن المستحسن.
* في حالة فقد الأنبوب بعد التثبيت ، تقلّص الحرارة بمدفع حراري مرة أخرى لجعله على اتصال وثيق بالمقبض.
* نظرًا لخصائص الأنبوب الواقي ، فإن الطول الكلي لديه تسامح حوالي زائد أو ناقص 3 مم ، وقد يكون الوجه النهائي مائلًا قليلاً ، لكنه ليس منتجًا معيبًا.
* القطر الداخلي للقبضة اليمنى هو .425.4. إذا كان صغيرًا أو فضفاضًا ، فاستخدم ختم الألومنيوم المرفق وضبط الفجوة بالمقبض.
* قد لا يكون متاحًا لسيارات SUZUKI ذات سعة البطارية المنخفضة وتوليد الطاقة وسيارات HONDA ذات البطاريات التي تقل عن 7S.
* سيارات YAMAHA يمكن استخدامها مع 4B5 أو أعلى المركبات التي تعمل بالبطارية.
[Compatibility]
・Handle Diameter: Φ22.2
・Grip outer diameter: Φ33
・Compatible grip length: 115 / 120 / 130mm
・Exclusive for 12V vehicles
[Components] Heat-shrinkable tube for grip protection
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up)
*When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve.
*Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind.
*Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use.
*If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life.
*The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect.
*The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip.
*This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S.
*Yamaha vehicles with 4B5 or higher batteries can be used.