لمدة 12 فولت دراجة نارية
لون فاتح: أبيض
6000 كلفن طريقة الإضاءة DC
معيار تفتيش الركاب مرت (25 ألف شمعة)
الفولطية المقدرة: 12 VDC
استهلاك الطاقة: HiBeam 20 W / LoBeam 20 W
الصمام: المصابيح XLamp XP-L المصنعة من قبل كري
درجة حرارة اللون: 6000 ك
* يجب تثبيت التثبيت بشكل صحيح وفقا لدليل التعليمات.إذا كنت تخطئ طريقة التثبيت فإنه يسبب الحريق ، عطل الخ.
* تأكد من إزالة رمز المحطة الطرفية على الجانب السلبي من البطارية قبل التثبيت ، وتأكد من أن المفتاح هو OFF.
* لا تلمس أو تلوث رقاقة LED. التصاق الأوساخ يسبب الحارقة من رقاقة LED بسبب الحرارة بالوعة.تعلق قبعة الاكريليك لمصباح LED مع ختم. بعد إزالة الغطاء وختم ، الأضرار لمصابيح LED بسبب الضمان هو خارج نطاق الضمان ، يرجى توخي الحذر.
* بما أن هذا المنتج هو أداة دقيقة ، يرجى توخي الحذر في التعامل معها. لا تسقطها أو تسحب الأسلاك بالقوة. التعامل غير الصحيح قد يسبب خلل ، حادث خطير مرتبط بالإصابة ، والحرق ، والحياة البشرية هناك أيضا خطر التسبب في شرارة ، فشل العزل ، قصر الدائرة ، وما إلى ذلك. قد يتسبب هذا المنتج في حدوث خلل أو حريق في السيارة ، لذا يرجى توخي الحذر.
* لا تحاول تفكيك أو إعادة تشكيل هذا المنتج ولا يمكن ضمان المنتجات المفككة / المُعاد تشكيلها.
* لا تنظر مباشرة إلى انبعاث LED داخل المصباح بينما تكون مضاءة. قد يسبب ضعف البصر.
* لا تقم برش الماء على العدسة أثناء الإنارة أو مباشرة بعد إيقاف التشغيل. سيؤدي ذلك إلى كسر العدسة ومصباح LED بسبب تغير درجة الحرارة المفاجئ. بالإضافة إلى ذلك ، يتم تسخين هيكل المصباح LED وإقامة المروحة الخلفية المركبة ووحدة التحكم إلى درجة حرارة عالية منذ ذلك الحين ، من فضلك لا تلمسها.
* بما أن هذا المنتج هو حصري للدراجات النارية ، فلا يمكن استخدامه للمركبات ذات الأربع عجلات.
* لا تضيء بالقرب من الورق أو القماش أو بالقرب من المواد القابلة للاشتعال لا تضيء أو تسبب تسخين غير طبيعي.بالإضافة إلى ذلك ، لا تضيء بالقرب من المواد القابلة للاشتعال مثل رذاذ قابل للاحتراق ، أرق الخ. والتهديد للقبض على النار يرجى القيام به.
* لا تعلق على المصباح في حالة مضاءة ، لأنها قد تسبب أعطال أو حروق.
* هذا المنتج مقاوم للماء ولكن ليس مقاوم للماء على الرغم من أنه مضاد للماء. يرجى القيام بمعاملة مقاومة للماء مع عامل السد. عن طريق التفاف الشريط الفينيل ، شريط لاصق النفس وما إلى ذلك. للمقرنة التي تخرج من وحدة تحكم. المياه مع الماء أكثر من اللازم يرجى تجنب.
* عند غسل السيارة بغسالة الضغط العالي ، من فضلك لا تضرب هذا المنتج مباشرة بغسل الضغط العالي.
* لا تسقط لمبة LED أو وحدة تحكم ، أو تعطي صدمة قوية ، وما إلى ذلك. لن يؤدي فقط إلى الإضرار ، أو تدهور الأداء ، أو تقصير العمر ، ولكن أيضًا يسبب الإصابة.
* لتثبيت لمبات LED ، تأكد من تطبيق شحوم السيليكون المقدمة على الأجزاء المحددة بعلامة الشحوم في دليل التعليمات.
* يرجى عدم تغطية المشجعين للماء ، يرجى ضمان مساحة كافية لتدفق الهواء امتص في الجزء الخلفي من المروحة.
* استخدم أقفال اللولب لمنع تفكيك الخيوط ، وإعادة تثبيتها بشكل دوري.
* يتطلب التثبيت معرفة ومهارة الخبراء ، يرجى القيام به في مصنع الصيانة المعين الخ. مع الميكانيكا الماهرة الخ
* يرجى التأكد من ضبط المحور البصري قبل الاستخدام.هناك إمكانية عرقلة رؤية المركبات المرتدة وإحداث حادث مروري.للمزيد من التفاصيل يرجى الرجوع إلى معايير السلامة لمركبات النقل البري.
* قد لا نتمكن من الحصول على ضمان من الشركة المصنعة للمركبة بسبب تركيب هذا المنتج.
نحن لسنا مسؤولين عن أي ضرر، الحوادث، الخ. بسبب استخدام هذا المنتج ، لا يمكننا تحمل المسؤولية على الإطلاق ، ونحن لا نتحمل أي مسؤولية عن رسوم الامتصاص والنفقات الأخرى التي تنشأ في الإصلاح. يرجى ملاحظة.
* إذا شعرت بأي شيء غير طبيعي أثناء التركيب أو أثناء الاستخدام ، يرجى الاتصال بالوكيل أو قسم الخدمات.
For 12V motorcycles
Luminescence Color: white
6000 Kelvin DC lighting system
Rated Voltage: DC12V
Power consumption: Hi beam 20W / Lo beam 20W
LED: CREE XLamp XP-L LEDs
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*Neo Factory will not be held responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.