- I bought this for use within MXCourse.It is heavy, stable, and sturdy.It does not break even when handled roughly and functions properly even when covered in dust and sand.So, it's like a "gush and dr...اقرأ أكثر
- As others have mentioned, if it's SEROW, you can't use the low MODE as is. It doesn't go under even if you stand up the car body. I put the rear wheel on top of two Veneer boards, and put the car body...اقرأ أكثر
- There is a STAND for each manufacturerMotorcycle, but I think it is the sturdiest and easiest to maintain.Thailand's STAND is more expensive and heavier than DCR's STAND, but it is not as easy to carr...اقرأ أكثر
- I'm using it with XR400R.TLM200R and this STAND is easy to useAlthough it is a little heavy, the weight gives you a sense of stability, and you can lift lightly and firmly even if the ground is gravel...اقرأ أكثر
- Tentatively good!This product is the first time to purchase Maintenance Stand, but for now there are no problems.Off If you are a car rider, I think that you understand, but after all I thought that M...اقرأ أكثر
- It is a replacement from the STAND with a common hydraulic damper of about five thousand yen.In the above STAND I tried to change it to make Thailand Chi due to the fact that it was somewhat shaky whe...اقرأ أكثر
- I bought it for Tire exchange and ChainMaintenance.From the result it is very easy to use.D ○ Even compared with C's, it is making it sturdier and there is a sense of security. Although hydraulic ...اقرأ أكثر
- Purchase Maintenance work of WR 250 R.I also thought of other Manufacturers, but took a sense of stability and made it Thailand.For Tire exchanges and car wash, there is nothing with Lift Stand and it...اقرأ أكثر
- I used it with XR 400 R, but I tried purchasing various Manufacturers but I think Thailand Chi was still the best. If you grab hang, you can easily Lift up without putting too much force, and stabilit...اقرأ أكثر
- I think that there are many types of cars that do not fit under your belly as this product is solid enough to make.However, since the Lift side is Rubber's Roller, you can place it between FWheel ...اقرأ أكثر
- Off First purchase was satisfactory. I arrived with assembled Grease up already done. Because my WR-X is protruding Fork, I put wood of about 2 cm under Tire and let STAND submerge. By the way the min...اقرأ أكثر
- It does not process anything to the minimum ground clearance of KLX 250 and can be slipped into Smooth. Lift up as soon as possible after arrival of goods - I tried Down, but without any oil pressure ...اقرأ أكثر
- Stability which cannot be felt by other Manufacturers (structure which carries out a Jack-up).By the vehicle type, adjustment is very pleasing, although it is required.It was lost that a Machine falls...اقرأ أكثر
- It purchased to the Chain Maintenances of the XG250 TRICKER without a Center stand.
Even if it made the STAND into the bottom position, it could not be made to have had to slide into under a car body...اقرأ أكثر - since I have participated in the Motocross race or the Enduro race well -- -- this Lift-up STAND is an indispensable Items.
Although the Lift-up STAND cheap until now was often used, since the pro...اقرأ أكثر - It mainly uses for maintenance of a TRIAL or a lightweight Off vehicle by Garage deferment.
Since the > top plates are two Rubber volume Pipes not a plank but approximately, even if a Under Guard is ...اقرأ أكثر
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING